Drayton digistat plus 3 manual

Install the 2 AA batteries provided Fig 6. Replace battery cover fig 7. The display shows the correct time and date which is. The temperature is controlled by sensing air temperature,. During adjustment the temperature will. Whilst in temperature override the pointer indicates both Man and.

Fig 1 shows. In this mode all pre-set. Fig 2. The screen will only show the temperature, which can be. The D. How to set my room temperature for my holiday period. When going on holiday you can lower the temperature of your.

The temperature will flash and by pressing. Fig 3b. Once you have set your time period the time will flash for T o exit the Holiday. When changing time the display will scroll through Hr Hours. The display will show holiday time period and set temperature. When the batteries start to run low a battery icon will blink for.

Please replace batteries with 2 x AA 1. It is activated. There should be no need to. Select Sunday. The time will now flash and can be. Change year. Fig Remove the battery cover using a coin. R eplace the spent. Replace the battery cover pressing fully home. When the display shows E1 or E2 this indicates a sensor fault and. Please contact your installer. Press the Y es — button. Y ou have. Press the Y es — button again. This tells. If you wish. The time will no w.

If y ou wish to alter the switching time. This will change. If you wish to alter. If y ou wish to alter any of the times. Once Mon. This means do. T elephone: Sales Fax: T echnical Helpline T elephone: Siebe Climate Controls continuously seek to improve products and reser ve the right The Digistat can be operated in one of three modes. If at anytime during normal oper ation, y ou wish to temporar ily increase or.

This can be done without entering the SET mode. The Digistat will now control the temper ature. If batter y replacement is. T o a void the possibility of ha ving to re- programme. In this. If the compar tment is left open f or longer , the unit. It ma y be necessar y. The batter y compar tment is situated at the bottom of the unit press to.

Ensure new batteries are installed correctly. The night setting can be programmed at whatev er time. This facility enables you to omit one or more of the switched periods. When one or more switching times are programmed together the later setting. For example , if all four switching times were set together. This resets the Digistat to. If during progr amming no button is pressed for between one and tw o minutes. Page Page 1 Page 2. Need help?

Post your question in this forum. Press the Yes — button. You have selected the Monday to Friday part of the programme. The battery compartment can now be left open, to replace the batteries, for approximately one hour. If the compartment is left open for longer, the unit will revert to the factory preset times and temperatures.

It may be necessary to reset the correct time of day after changing the batteries. The battery compartment is situated at the bottom of the unit press to unlatch and slide down. When the display is as shown here, press the Yes — button if you wish to view or alter the times for Sat. Repeat steps as required. The night setting can be programmed at whatever time you require, even after When one or more switching times are programmed together the later setting takes precedent.

For example, if all four switching times were set together the Digistat would control continuously at the fourth night temperature setting. Press the Yes — button again. This tells you that at 6. The time will now flash. This will change the switching time in 10 minute steps.

The Digistat will now control the temperature to the override setting until the next programmed switching time, when it will revert to the times and temperatures you have already programmed. This means do you want to set the times for Monday 1 differently from the rest of the week? If you do, press the Yes — Button, and follow the routine as steps 9 to This signifies that two 1. If battery replacement is Diagram C carried out in this condition the programmed settings will only be held in the memory for a maximum of one minute, after which re-programming may be necessary.

IMPORTANT To avoid the possibility of having to re-programme the switching times and temperatures, it is advisable to wait until the display with a flashing battery symbol changes to a continuous battery only display after 30 days — Diagram D.